Linksys WiFi Extender Blinking Red? Ways to Fix It

Trying to establish a connection between your new Linksys WiFi extender and router? Or attempting a Linksys Extender setup? You might encounter a Linksys WiFi extender blinking red light issue. Generally, this is not a big issue, but sometimes, it may frustrate you badly. Fortunately, you can resolve this issue using some smart steps that we will be sharing with you in this piece of information. Let’s get started!

7 Smart Ways to Fix Linksys Blinking Red Light Issue

There are several steps that you can try out to resolve the Linksys WiFi extender blinking red light issue. Some are very basic steps like power cycling the device while there are a few hacks that you may not know about. Let’s have a deep look at the 7 most effective smart ways to resolve the red light issue in your Linksys WiFi device.

Power Cycle the Device

Generally, when an error occurs in an electronic system such as a mobile phone or laptop, the first thing that comes to our mind is to power cycle the device. You need to perform the same thing whenever you notice your Linksys WiFi extender blinking red. Simply, turn off the power switch or button on your Linksys WiFi extender and then unplug the power adapter of the device. Wait for a couple of minutes and then plug in the power adapter and switch the device on. Keep an eye on the LED, it might not blink red again. But, if the blinking behavior of the Power LED continues, you can try out the next step.

Ensure a Consistent Connection Between the Modem and Extender

Probably, your Linksys WiFi range extender is not firmly connected to your router or modem. Or it is possible that you inserted one or both chords of the ethernet cable into the wrong ports. Check for the same before beginning the Linksys WiFi Extender Setup and re-insert both chords into the correct port of the router and Linksys extender. Once done, power cycle the device and wait for the red light to flash. If the Linksys blinking red light issue doesn’t get resolved, try another hack as explained below.

Check For Network Congestion

Network congestion is basically a situation referring to the traffic of networks. For example, if there are too many devices connected to your Linksys WiFi network, this is called network congestion. Check for the same whenever you notice your Linksys WiFi extender blinking red. Try to disconnect some devices which are unnecessary. This should probably fix the Linksys Velop Red Light issue. If this hack also does not work in your case, you need to keep trying other hacks that are not tried out yet.

Repair Weak Data Signal Strength

Weak signal strength between your router and Linksys WiFi extender could be a major cause for a blinking red light. You can fix this problem either by reducing the distance between the two devices or by removing the objects that interfere with the signals such as baby monitors. In addition, try placing your router and extender away from the walls and floors because these elements are the biggest reasons behind network interruptions. We recommend you place your WiFi device in the central location at your home. This is ideal for achieving the speed and coverage that you expect from your wireless WiFi system. And it may also fix the blinking red light issue that you may be facing.

Update the Firmware of Your WiFi Devices

Firmware is an operating system of any wireless WiFi device like routers, extenders, and access points. Similar to any other devices like computers and laptops, wireless WiFi devices cannot function properly without updated firmware. With this in mind, we can say that it could also be a possible reason behind your Linksys WiFi extender blinking red light issue. So, check for firmware updates if available by accessing the Linksys Admin panel. If an update is available, simply run the update and install it.

Reset Your Linksys Extender Device

Resetting a Linksys WiFi extender device deletes all the data including user ID, password, etc. Therefore, you should consider this step as the last DIY step. To do this process, locate the “Reset” or Factory Reset” button on the rear or bottom panel of the device. Then you just need to press and hold the button for a few seconds until the Power LED on the device starts flashing. Your Linksys WiFi extender device will automatically reset its settings to factory default settings. Once the process is completed, you need to power cycle the device. You may not see the Linksys blinking red light again. But, if you notice the blinking red light again, your next step should be contacting our technical support experts without a doubt.

Contact Our Support Experts

Lastly, if nothing works, there could be an unknown issue with your Linksys WiFi extender. It is important to first correctly identify the error. Our technical support experts can help you with this and solve the issue. Reach out to them using the contact details we have provided at the top of this page. They will take a couple of minutes to understand your Linksys blinking red light problem, then identify the actual cause, and finally provide you with the most appropriate solution. The complete process will barely take 10-20 minutes. And we assure you that contacting our support team will be worth your time.

Hope you loved this piece of information and it may help you resolve your Linksys WiFi extender blinking red light issue. For more quality and useful posts, stay tuned with us.

---