Linksys Extender Blinking Orange? Get It Fixed Now!

Although the Linksys extender is a safe and useful product that works to improve your existing signals significantly. However, sometimes experiencing issues with the extender like the Linksys extender blinking orange can be annoying for you. The situation can be worsened if you are unable to solve that error yourself. But, the resolving tips mentioned in this blog will surely work for your extender error. Check them out and implement them in the right sequence.

Reasons Behind Linksys Extender Blinking Orange

As a blinking light is always an indicator of a dangerous situation, the same case can be with the Linksys extender blinking orange error. There could be a number of causes that can lead to an error in the network. But, most probably, there is a weak or no connection between the extender and your existing router. Whereas, the other possibilities can be incorrect configuration, firmware issues, or an interrupted power supply to the extender. So, it is advisable to identify the root cause of the error so that you can take relevant troubleshooting tips into account.

Check The Connection Strength

Before anything else, try to check the most probable cause which is the interrupted connection between your router and extender. As the Linksys extender blinking orange error could occur due to that reason, so rectify this thing first. Ensure both devices are in a strong connection with maximum signal strength. A loose, broken, or faulty connection can force the extender to blink orange and create network problems.

So, try creating the connections again after disconnecting the devices once. In addition to that, verifying the connection between your device and the network is also quite necessary. Check whether your networked device is well connected to the extender network or not. For a wireless connection, make sure your device is actually networked with your own network instead of someone else’s. Whereas, in the wired connection, be sure the ethernet cable and the ports are in well working condition. If you find any damaged wire, replace that with a new one.

Reboot The Extender

Rebooting the extender can help remove technical bugs from the extender if there are any. So, discard the extender from the current power outlet and wait for a short while and keep it discarded. Later, plug the extender again but choose another socket this time as the older one can be broken or have any error. Allow the extender to boot up properly and check whether the Linksys extender blinking orange error resolves or not.

Change The Extender Placement

While rebooting the extender, you must prefer to choose another location for the extender. The far distance between the extender and router can create issues in the network and connection. So, try placing it halfway to your house and enough closer to the existing router. Moreover, place the extender at least two feet above the ground like on any shelf or somewhere else. Which must be far away from the electrical appliances that interrupt signals by absorbing them.

Still Linksys Extender Blinking Orange? Reset It!

Last but not least solution here is to reset the extender and configure it again. The imperfect installed settings might force the extender to reset once to remove the blinking orange light issue. As you do this process, the older installed settings will discard and it will also help to resolve the Linksys extender blinking orange error.

Press the dedicated reset button from the extender and hold it until you see another blinking light on its panel. Wait for some time and let the extender reset the settings as this will take a few minutes to complete. After resetting it, do the Linksys WiFi extender setup again either using its WPS button or by following the screen directions of the web portal.

Setup Through Web Browser

To make your extender ready to use after resetting it, carry out its setup process on the web setup window. Go to the setup page on your networked device using the web browser and the default web or IP address. Type any of those addresses into the browser’s search field and click enter and the Linksys extender login page will open up on the screen.

Insert the default username and password in the login fields and click login after that. From the next page, choose the network that you want to extend and click on the Extend button. Thereafter, the browser screen will direct you until you complete the setup process in the right manner. Finally, start enjoying the uninterrupted and extended network by connecting your device to it.

Now, confirm that you succeed in resolving the Linksys extender blinking orange error once you use these tips. However, if still, you are struggling with the same problem you can reach out to our Linksys Technical Experts for more guidance. We will make the further troubleshooting process simple for you to get the error clear.

---